Happymodel Mobula6 ELRS 1s 65mm Brushless FPV Whoop Drone - 2.4GHz ELRS SPI Receiver

FPV Brushless Whoop Drone Happymodel Mobula6 ELRS Overview ExpressLRS is currently the most popular remote control link system. It has the characteristics of low latency and high packet rate, and its link quality is very reliable. Now we are about to release Mobula6 equipped with ExpressLRS RC link system, the new Mobula6 elrs would coming out with a new 0702 brushless motor, that would be the lightest brushless motors all over the world. We're sure this would be a good option for you in the Tiny Whoop Season. Features:AIO Flight controller with ELRS Receiver and 5.8G VTXSuper light 1S 65mm Brushless whoop only 18.7gEquipment with the lightest brushless motors-SE0702 only 1.46gramRuncam Nano3 The lightest 1/3 CMOS 800TVL Camera Smooth and powerfulCompatible for 1S Lipo/LIHVSpecifications:Brand Name: HappymodelItem Name: Mobula6 ELRS 1S 65mm Brushless whoop drone BNF versionWheelbase: 65mmSize: 80mm*80mm*37mmWeight: 18.7gReceiver option:2.4GHz ExpressLRS SPI receiver915MHz ExpressLRS Serial-based receiver868MHz ExpressLRS Serial-based receiver Spare parts specifications:Motor:Mode: SE0702 KV26000Configu-ration:9N12PStator Diamter:7mmStator Length:2mmShaft Diameter:Φ1mmMotor Dimension(Dia.*Len):Φ9.5mm*14mmWeight(g):1.46gNo.of Cells(Lipo):1S only Propellers:HQprop31mmx2Center Thickness:5mmProp Disk Diameter:31mmCenter Hole Inner diameter:1.0mmWeight:0.2g Flight Controller:ELRS F4 2G4 flight controller built-in SPI expresslrs 2.4G receiverCrazyF4 ELRS flight controller built-in 915MHz expresslrs receiverCrazyF4 ELRS flight controller built-in 868MHz expresslrs receiverMCU:STM32F411CEU6 (100MHZ, 512K FLASH)Sensor: MPU-6000(SPI connection)Board size: 28.5 * 28.5MMPower supply: 1S battery input (DC 2.9V-4.35V)Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 readyBuilt-in Betaflight OSD(SPI Control)Built-in 5.8G VTXBuilt-in ExpressLRS 2.4G/915MHz/868MHz receiverBuilt-in 5V 1A BECBuilt-in voltage detection Onboard 4in1 ESCMCU upgraded to EFM8BB21Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds)Support BLHeliSuite programmableFactory firmware: O_H_5_REV16_7.HEXDefault protocol: DSHOT600 Onboard SPI ExpressLRS 2.4GHz ReceiverPacket Rate option: 25Hz/50Hz/150Hz/250Hz/500HzRF Frequency: 2.4GHzAntenna : SMD antennaTelemetry output Power: <12dBmReceiver protocol: SPI ExpressLRSCould bind with Happymodel ES24TX , ES24TX Lite, ES24TX Slim and DIY 2.4GHz ELRS TX module ExpressLRS version 1.0.0 or 1.0.1 both compatible Onboard Serial-based ELRS ReceiverOperation current: ~100MaRx To FC protocol: CSRFRF Frequency optional: 915mhz or 868mhz(EU)Antenna connector: IPEX4Telemetry output Power: <17dBmFirmware target: Happymodel_RX_ES915RXReceiver protocol: CRSFCould bind with Happymodel ES915TX , Frsky R9M and DIY ELRS TX module(need to flash the same version ELRS firmware)Firmware flash via Betaflight pass-through Onboard 5.8g VTXOutput power: 25mw~200mwFrequency: 40CHInput voltage: 3.3V 5.5VCurrent consumption: 300mA(type)Frequency: 5.8GHz 5bands 40 channelsWith Race band Smartaudio ready Runcam Nano3Model: RunCam Nano 3Image Sensor: 1/3" CMOSHorizontal Resolution: 800TVLLens: 2.1mm(M8) FOV 160° Signal System: PAL/NTSC Non SwitchableS/N Ratio: >50dBElectronic Shutter Speed: AutoAuto Gain Control (AGC): AutoMin. Illumination: [email protected]: AutoDay/Night: ColorPower:DC 3-5.5VCurrent: 110mA@5V [email protected] Material: ABSNet Weight: 1.2gDimensions: L14mm*W14mm*H9mm Lipo BatteryCapacity:300mAhVoltage:3.8vContinuous Discharge Rate: 30CSize: 57mmx12mmx7mmWeight: 8gConnector: PH2.0 Pacakge Included:1*Mobula6 1S 65mm whoop Drone FrameReceiver optional:2.4GHz ExpressLRS SPI receiver Or915MHz ExpressLRS Serial-based receiver Or868MHz ExpressLRS Serial-based receiver4*SE0702 KV26000 brushless motor1*HQPROP 31mm bi-blade propellers(4cw+4ccw)1*Runcam Nano3 1/3 CMOS 800TVL camera1*Onboard 5.8G 25mw~200mw VTX4*1S 300mah 30C LiHV Battery1*1S Lipo/LIHV USB Charger1*Propeller disassemble tool