HappyModel Mobula6 2024 1S 65mm Ultra Light Micro FPV Whoop BNF 2.4GHz ELRS Receiver 5.8G Openvtx - US Only

Recommended Match (1)Jumper Bumblebee HALL/RDC50 ELRS 2.4G FPV Controller Compact & Full-Featured FPV (2)RadioMaster Pocket 2.4GHz 16CH ELRS/CC2500 Hall Gimbals Radio Controller for FPV Racing Drones In stock now Mobula6 2024 1S 65mm Ultra Light Micro FPV Whoop BNF 2.4GHz ExpressLRS Receiver 5.8G Openvtx Features:AIO Flight controller with Serial ELRS Receiver and 5.8G OpenvtxSuper light 1S 65mm Brushless whoop only 17.7gEquipment with the lightest brushless motors-SE0702 only 1.46gramFX17-B 1/3 CMOS 800TVL Camera awesome footageSmooth and powerfulCompatible for 1S Lipo/LIHVSpecifications:Brand Name: HappymodelItem Name: Mobula6 2024 1S 65mm ultra light micro FPV WhoopWheelbase: 65mmSize: 81mm*81mm*37mmWeight: 17.7g Motor：Mode: SE0702 KV28000Configu-ration:9N12PStator Diamter:7mmStator Length:2mmShaft Diameter:Φ1mmMotor Dimension(Dia.*Len):Φ9.5mm*14mmWeight(g):1.46gNo.of Cells(Lipo):1S onlyPropellers：Materials: PCInch: 31mmPitch: 0.8 inWeight: 0.21gMount hole diameter: 1mmFlight controller：SuperX ELRS AIO 5-IN-1 Flight controllerMCU:STM32F411CEU6 (100MHZ, 512K FLASH) ,ESP32-PICO-D4Sensor:BMI270(SPI connection)Mount hole size: 25.5mm*25.5mmPower supply: 1S battery input (DC 2.9V-4.35V)Built-in 5A(each) Blheli_S 4in1 ESCBuilt-in Betaflight OSD(SPI Control)Built-in 5.8G OpenVTX 0mw~400mw (MSP control)Built-in UART ExpressLRS v3.0.0Built-in voltage meter sensor, voltage meter scale 110Built-in current meter sensor, current meter scale 1175Onboard 4in1 ESC：Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)Support BLHeliSuite programmableFactory firmware: Bluejay v0.19.2Default protocol: DSHOT300Recommend ESC Startup power value to min1100/max1200Onboard Serial ExpressLRS receiver：Packet Rate option: 50Hz/150Hz/250Hz/500HzExpressLRS Firmware version: V3.0RF Frequency: 2.4GHzAntenna : Enameled copper wire antennaTelemetry output Power: <12dBmReceiver protocol: Serial_based CRSFCompatible with ExpressLRS V3.x.x TX ModuleCould flash single ELRS receiver firmware by WifiExpressLRS firmware target: Generic ESP32 2.4Ghz RX and VTXOnboard 5.8g VTX:Firmware version: OPENVTXMSP VTXPIT Mode supportChannels:40chTransmitting Power: 0/RCE/25mw/100mw/400mwPower supply: DC 5VCurrent (5v): <650ma (400mw)Antenna connector: U.FLFX17-B Camera:Model:FX17-BImage Sensor: 1/3″ CMOSHorizontal Resolution: 800TVLFOV 150°Signal System: NTSCNet Weight: 1.5gDimensions: L14mm*W14mm*H13mm Package Included:1x Mobula6 2024 1S 65mm whoop Drone Frame +Canopy1x SuperX ELRS AIO 5-IN-1 Flight controller4x SE0702 KV28000 brushless motor1x Gemfan 1208-3 31mm tri-blade propellers(4cw+4ccw)1x FX17-B 1/3 CMOS 800TVL camera NTSC 4:31x Onboard 5.8G 25mw~400mw VTX1x Spare canopy1x Propeller disassemble tool1x Screw driver Factory firmware and default dump file (Compatible with both V1.0 and V2.0 version flight controller) :Mobula6 2024 factory firmware 4.4.0Dump file for Mobula6 2024 with Betaflight 4.4.0Mobula6 2024 Factory firmware 4.4.2Dump file for Mobula6 2024 with Betaflight 4.4.2 Mobula6 2024 1S 65mm micro fpv whoop manual Mobula6 ECO 2024 1s micro FPV Whoop manual The AIO flight controller comes with two type of Gyro sensor , one is BMI270 and another one is ICM42688P So after you re-flashed firmware ,First Gyro direction for BMI270 should set to be CW0° , and for ICM42688P should set to be CW90° The easiest way to differentiate between BMI270 and ICM42688P: BMI270 Gyro sensor with 3.2kHz gyro update frequence ICM42688P Gyro sensor with 8kHz gyro update frequence Port settings: Receiver and telemetry settings: