Happymodel Crux3 1S ELRS Toothpick Compatible with CaddxFPV Peanut and Insta360 GO2

Happymodel Crux3 1S ELRS 3inch toothpick FPV Racer Drone Note: The Caddx peanut camera is not included, you can buy it HERE Recommended Batteries (Click the picture for the product link): Notice: Insta360 GO2 and CaddxFPV Peanut cameras are not included. Key Features Lightweight 1S brushless toothpick drone – only 40g (without battery) All-in-one flight controller with integrated ELRS 2.4GHz receiver and 5.8GHz VTX Equipped with Caddx Ant 1200TVL Global WDR FPV camera Powered by EX1202.5 KV11500 brushless motors Recommended battery: 1S 450mAh / 650mAh / 660mAh / 720mAh Compatible with Insta360 GO2 and CaddxFPV Peanut mounts Up to 4.5 minutes flight time with 650mAh while carrying Peanut Specifications Brand Happymodel Model Crux3 1S ELRS Wheelbase 115mm Size 97 x 97 x 35 mm (without propellers) Weight 40g (without battery) Package Includes Item Quantity Crux3 Frame and Canopy 1 ELRS F4 2G4 Flight Controller (SPI ExpressLRS 2.4G Receiver) 1 EX1202.5 KV11500 Brushless Motors 4 Gemfan 75mm Bi-blade Propellers (4CW + 4CCW) 1 Set Caddx Ant 1200TVL Camera 1 5.8G 25mW~200mW VTX (built into flight controller) 1 Screwdriver 1 Propeller Removal Tool 1 3D Printed Mount for Insta360 GO2 / CaddxFPV Peanut 1 Happymodel Handbag 1 Motor Specs (EX1202.5 KV11500) Configuration: 9N12P Stator Diameter: 12mm Stator Length: 2.5mm Shaft Diameter: 1.5mm Motor Size: 14mm x 14.5mm Weight: 4.4g Voltage: 1S Flight Controller MCU: STM32F411CEU6 (100MHz, 512K Flash) Sensor: MPU-6000 (SPI) Input Voltage: 1S (2.9V~4.35V) Built-in 5A BlHeli_S 4-in-1 ESC, DShot600 ready Integrated Betaflight OSD, 5.8G VTX, 5V 1A BEC Firmware Target: CRAZYBEEF4SX1280 ESC Specs MCU: EFM8BB21 Current: 5A continuous, 6A peak (3s) BLHeliSuite programmable Default protocol: DSHOT300 SPI ExpressLRS 2.4GHz Receiver Packet Rates: 25/50/150/250/500Hz RF Frequency: 2.4GHz Antenna: SMD Telemetry Power: <12dBm Compatible with all ExpressLRS 2.4GHz TX modules Firmware version required: ≥ 1.0.0 5.8GHz VTX Output Power: 25mW~200mW (adjustable) Voltage Input: 3.3V~5.5V Current: 300mA (typical) 40 channels, 5 bands with Raceband Smartaudio supported Caddx ANT Camera Image Sensor: 1/3" CMOS Resolution: 1200TVL Aspect Ratio: 4:3 / 16:9 Min Illumination: [email protected] Lens: 1.8mm WDR: Global WDR Dimensions: 14x14mm (with bracket: 19x19mm) Input Voltage: DC 3.7V~18V Weight: 2g Manual: Happymodel Crux3 1S ELRS V2.0 with ELRS 2G4 V3.2 manual document Hex file: Betaflight_4.3.0_CRAZYBEEF4SX1280_b2deec171 Diff file: Crux3 1S ELRS 2G4 V3.1 V3.2 Diff for Betaflight_4.3.0_CRAZYBEEF4SX1280 support ELRS V2.0 Dump file for Betaflight 4.4.2: Crux3 1S ELRS 2G4 V3.1 V3.2 Dump for Betaflight_4.4.2_CRAZYBEEF4SX1280 support ELRS V3.0